{"id":3514,"date":"2026-10-08T22:06:17","date_gmt":"2026-10-08T14:06:17","guid":{"rendered":"http:\/\/www.ars-infosys.com\/blog\/?p=3514"},"modified":"2026-10-08T22:06:17","modified_gmt":"2026-10-08T14:06:17","slug":"what-is-the-pressure-rating-of-submersible-pumps-483e-95fe0c","status":"publish","type":"post","link":"http:\/\/www.ars-infosys.com\/blog\/2026\/10\/08\/what-is-the-pressure-rating-of-submersible-pumps-483e-95fe0c\/","title":{"rendered":"What is the pressure rating of submersible pumps?"},"content":{"rendered":"

Hey everyone, it\u2019s Jake here, and I run that submersible pump supply company you\u2019ve probably seen around a few pump forums. Today I want to talk about something that comes up every single week in my DMs: pressure ratings for submersible pumps. Most of the time, folks come to me thinking \u201cit\u2019s just a number, right? Higher is better\u201d \u2014 and yeah, sure, sometimes, but there\u2019s way more to it than just grabbing the first pump with a big pressure rating. Let\u2019s break this down like we chat over a coffee, no boring industry jargon dumped on you. Submersible Pump<\/a><\/p>\n

<\/p>\n

First, let\u2019s get one basic definition out of the way fast: when we talk about a submersible pump\u2019s pressure rating, we\u2019re not talking about PSI like the air in your car tires \u2014 though they\u2019re related, just way bigger. Mostly, it\u2019s measured in what\u2019s called \u201chead,\u201d which stands for total dynamic head, and that\u2019s the vertical distance water has to move from the pump itself up to the highest point it needs to get to. Think of it like this: if your well is 100 feet deep, and your sprinkler system\u2019s line is another 20 feet above ground, that\u2019s 120 feet of head you need the pump to cover. Got it? Good, because that\u2019s way easier to wrap your head around than random PSI numbers.<\/p>\n

Now, why does pressure rating matter so much for submersible pumps, not like the sump pump in your basement that just moves water a few feet? Because these bad boys are underwater \u2014 deep underwater. If you\u2019re putting a pump in a 500-foot deep well, the pressure from the surrounding water alone is already pretty intense. You need a pump that can handle that external pressure, plus the internal pressure from pushing water all those feet up. Mess that up, and either the pump\u2019s housing cracks from outside pressure, or the motor burns out trying to push water that doesn\u2019t have enough internal pressure to move.<\/p>\n

Let\u2019s get real about common misconceptions here. I\u2019ve had so many customers say \u201cI need a 100 PSI pump, no exceptions\u201d \u2014 but PSI is actually just another way to convert head, right? One PSI is roughly 2.31 feet of head. So a 40 PSI pump is about 92 feet of head, a 60 PSI is ~138 feet, and so on. If you\u2019re pumping from a 100-foot well, a 100 PSI pump is overkill \u2014 that\u2019ll cost you way more upfront, waste energy every month, and actually might cause issues because it\u2019s pushing water too fast through your pipes, leading to more wear and tear on them and the pump itself. That\u2019s a mistake I see all the time, and it\u2019s so avoidable if you just do a quick measurement of your total vertical distance.<\/p>\n

Wait, but hold on \u2014 pressure rating isn\u2019t just about vertical head, is it? Oh man, no. There\u2019s also what\u2019s called friction loss. If you\u2019re pushing water through 1,000 feet of 1-inch pipe, that\u2019s way more friction than 500 feet of 2-inch pipe. So your total required pressure goes up because the water has to fight that friction as it moves through the pipes. That\u2019s another thing I walk every customer through when they reach out \u2014 I don\u2019t just ask \u201chow deep is your well\u201d and send a pump; I check the pipe size, how far the pump is from the house or tank, even how many elbows or turns there are in the line, because every little bit adds up to pressure the pump needs to provide.<\/p>\n

Now, let\u2019s talk about different types of submersible pumps and their pressure ratings, because not all are built the same. For residential well pumps, most are rated for 40 to 60 PSI, which works for most homes \u2014 50 PSI is a sweet spot for pressure at your faucets and showers, right? If you need more for a sprinkler system that\u2019s spread out, maybe 80 PSI, but that\u2019s still not crazy. Then there are the ones for commercial or agricultural use \u2014 think irrigation systems that cover acres, or pumps for deep municipal wells. Those can go up to 200 PSI or even higher, depending on how deep the source is. We once had an agricultural customer who needed a pump for a 1,200-foot deep well for his cattle troughs, so we sent him a pump rated for 180 PSI \u2014 that was the sweet spot for his total head and friction loss, and he\u2019s been running it for 5 years without a single issue.<\/p>\n

But here\u2019s the part most manufacturers won\u2019t tell you: pressure ratings are often tested in ideal conditions. That means no friction loss, straight vertical pipe, no extra turns, just the pump in a tank pushing water straight up. Real life is never that simple. So when we send a pump to a customer, we always adjust the rating for their actual setup, not just the test number. That\u2019s why a lot of folks come to us after getting a pump from a big box store that \u201csaid\u201d it could do 150 feet of head, but only pushes 100 feet in real life \u2014 because the test was in perfect conditions, and their well has a bunch of pipe turns and a horizontal run that adds friction.<\/p>\n

Another big factor: the pump\u2019s depth rating, which is different from its pressure rating, but tied to it. A pump that\u2019s rated to sit 500 feet underwater has to handle the external hydrostatic pressure from that depth \u2014 that\u2019s the pressure of the water around it, pushing in on the pump\u2019s housing. If you put a pump rated for 100 feet deep into a 300-foot deep well, the outside pressure will crush the housing, or cause seals to leak, letting water get into the motor and burning it out. That\u2019s why we always make sure the pressure rating matches both the depth of the well AND the required vertical lift to the surface. You can\u2019t separate those two.<\/p>\n

I also get asked all the time: what happens if a pump\u2019s pressure rating is too low? Well, first you get low water pressure at your taps, that\u2019s obvious. But more importantly, the pump will cycle on and way too frequently \u2014 it\u2019ll run non-stop trying to push water, which wears out the motor a lot faster. Over time, that leads to premature pump failure, and no one wants to replace a $1,500 pump every 2 years, right? On the flip side, too high a pressure rating? Like I said before, that\u2019s wasted energy \u2014 you\u2019re paying to push water faster than you need to, leading to higher electricity bills, and also the extra pressure can damage your pipes, your pressure tank, or even your appliances like dishwashers or washing machines. We once had a customer who put a 100 PSI pump in his home, and his water heater sprung a leak after 6 months because the pressure was too high \u2014 we had to adjust the pressure switch and add a pressure relief valve to fix that.<\/p>\n

So how do you figure out the right pressure rating for your submersible pump? It\u2019s not rocket science, but it does need a few measurements. First, measure the static water level in your well \u2014 that\u2019s how deep the water is from the ground surface, not the depth of the pump (you usually set the pump 10-20 feet above the bottom to avoid sucking up sediment). Then measure the drawdown level, which is how deep the water gets when the pump is running. That\u2019s your total vertical lift from the water level to your outlet point (faucet, tank, sprinkler). Then add friction loss \u2014 a general rule of thumb is 5 PSI per 100 feet of horizontal pipe, and more if you have small pipe or lots of turns. Add all that up, and that\u2019s your minimum required pressure, plus a little extra buffer to account for wear on the pump over time.<\/p>\n

At the end of the day, pressure ratings aren\u2019t just a random number on a spec sheet \u2014 they\u2019re what make sure your submersible pump works when you need it, for years, not just until the warranty runs out. I\u2019ve been in this game for 12 years, and I\u2019ve seen so many people skip the basics and end up with a pump that doesn\u2019t work for their setup, so they have to spend more money replacing it or fixing it. That\u2019s why I always tell people: don\u2019t just look for the highest pressure rating you can find. Think about your actual needs, do the math, and if you\u2019re not sure, reach out.<\/p>\n

<\/p>\n

If you\u2019re shopping for a submersible pump and you\u2019re confused about pressure ratings, or you just need help figuring out what you need for your well, irrigation, or whatever project you\u2019re working on, hit us up to talk through it. We don\u2019t do pushy sales, we just give you straight answers based on what works, not what makes us the most money.<\/p>\n

Submersible Pump<\/a> References:<\/p>\n

    \n
  1. Submersible Pump Installation and Maintenance Guide, National Ground Water Association<\/li>\n
  2. Hydraulics for Irrigation and Water Supply, FAO Water Reports<\/li>\n
  3. Pressure Rating Standards for Submersible Pumps, Underwriters Laboratories (UL)<\/li>\n<\/ol>\n
    \n

    Henan Yibeng Pump Industry Co., Ltd.<\/a>
    Henan Yibeng Pump Industry Co., Ltd. is one of the leading submersible pump manufacturers and suppliers in China. We warmly welcome you to buy high-grade submersible pump from our factory. All equipment are with high quality and competitive price. Contact us for more details.
    Address: Fengqiu County, Zhaogang Town, Xinxiang City, Henan Province, China.
    E-mail: info@hnybpumps.com
    WebSite:     https:\/\/www.hnybpumps.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    Hey everyone, it\u2019s Jake here, and I run that submersible pump supply company you\u2019ve probably seen … What is the pressure rating of submersible pumps?<\/span>Read more<\/a><\/p>\n","protected":false},"author":114,"featured_media":3514,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3477],"class_list":["post-3514","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-submersible-pump-4d5c-964c2f"],"_links":{"self":[{"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/posts\/3514","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/users\/114"}],"replies":[{"embeddable":true,"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/comments?post=3514"}],"version-history":[{"count":0,"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/posts\/3514\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/posts\/3514"}],"wp:attachment":[{"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/media?parent=3514"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/categories?post=3514"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.ars-infosys.com\/blog\/wp-json\/wp\/v2\/tags?post=3514"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}